LED Strip Light Installation Guide

Introduction

We always go the extra mile to ensure they're top quality and built to light up the spaces you love for years. Follow this easy guide to help you create the look you’ve been dreaming of with the best results. We’re also here if you need other design and installation tips or answers to any questions—let’s make your project a success!

UL Listing and Compliance Information

Our LED Strip Lights are UL listed in the USA and Canada. This means they are safe to use and free from any hazardous substances. To comply with UL standards and inspections, please keep in mind that:

• A Class 2 power supply must be used with each run of lights.
• Each installation of LED strip lights in series should consume no more than 100W max.

Español

• Debe utilizarse un transformador de Clase 2 cuando sea necesario ajustarse a las normas de seguridad UL.
• La instalación no debe exceder un máximo de 100W cuando se conecten en serie las cintas LED.

Français

• Pour être conforme aux règles de sécurité, une source d'alimentation de Classe 2 doit être utilisée.
• L'installation ne doit pas dépasser un total de 100W lorsque les rubans LED sont montées en série.

Installation Instructions

We know you’ve got a clear vision and a stunning end result in mind. All it needs now is the right technical planning, like where your driver and dimmer will go. Your LED strip light should be installed on a clean, flat surface using the 3M adhesive backing or mounting clips. We recommend aluminum so your strip stays cool and works its best for years to come.

1. Component Check

On a clean surface, gently unroll the LED strip lights from the plastic reel and lay out all components. Make sure you have everything you need to complete the installation:

Double-check that your power supply matches the voltage of your LED strips and can handle the entire load of the LEDs.

For longer runs of LED strips, be mindful of the strip’s maximum run length. If you need a longer run than the maximum, you may need to install the strips in parallel from the power source.

2. Mock Installation

Before peeling the adhesive backing or cutting the strip, complete a mock installation to test and turn on your lights. Connect your LEDs to your dimmer and power supply.

Note: In this example, we are using a wireless dimmer and receiver.

3. Troubleshoot If Needed

The strips should light up. If they don’t, please check your connections and make sure the polarities from the power supply to the LED strip match (positive to positive, negative to negative).

The strip has markings (+ and - symbols) to indicate polarity.

4. Check Your Components

Verify that the chosen brightness and color temperature match your vision.

5. Turn Power Off at the Circuit Breaker

Turn off the power to the LED strip light and power supply. Then, disconnect the strip from the power supply or controller.

6. Cut the LED Strip Light to the Required Length

Decide how long you want your LED strip to be and measure carefully for precise cuts. Using sharp scissors, cut the strip only at the black cut marks located between the copper solder pads. Make sure to cut on the copper pads, not on the solder joints.

Special Cases When Using Solderless Grip Connectors

When using solderless connectors with the following LED strips, you will need more copper pad to work with:

• Outdoor (IP65) Accent™
• Outdoor (IP65) Architectural™ Tunable White
• Outdoor (IP65) Accent™ Tunable White
• Outdoor (IP65) Sienna™ Dim-to-Warm
• Outdoor (IP65) RGB 600
  

Cut both solder pads so the strip section has enough surface area to fit securely into the connector head.

7. Make Sure Polarities Are Matched Throughout the Setup

When installing separate segments of the LED strip together, either by soldering or using connectors, always ensure that the polarity is matched from one strip to the next. In other words, always match the + and - markings.

8. Retest Your Setup

Test the strip again to make sure they all light up and are functioning properly before the final installation. Once you have verified all segments are working, you’re ready to install them.

9. Prepare Your Surface for Installation 

Thoroughly clean any surface where you will be attaching your LED strip lights. The adhesive backing is strong, but it will not stick to dirty or dusty surfaces.

10. Attach the LED Strip Light

Peel the cover of the 3M adhesive backing a few inches at a time while gently pressing the strip against the installation surface. Make sure the strip is firmly attached to the surface.

11. Complete All Connections

Complete the connections and wiring between your power supply, dimmers, controllers, or connectors.

12. Enjoy Your Lights!

Turn the power back on at the circuit breaker and enjoy the glow!

Because of our commitment to you, we stand by our products. We are always available to answer any questions or troubleshoot any unlikely issues.

Warranty

We've got you with our industry-leading coverage!

We use the highest-quality components in our LED strip lights, drivers, controllers, and accessories. We know you don’t run your lights 24/7, so we’ve shaped our warranty to reflect your day-to-day use and long-lasting performance.

For that reason, we offer industry-leading 15-year coverage on most of our LED strip lighting products and prolonged warranties on drivers, controllers, dimmers, and accessories. Please read our warranty policy to learn about timeframes and exceptions.

Safety & Disclosures

Need Help Finishing the Job?

We’ve covered the basics. But if something’s not quite adding up or your setup looks a little different, we're here to help!